Ford Ignition Lock Cylinder Removal Without Key
The ignition lock cylinder is a part of the ignition system in a car. It is located in the steering column and it is responsible for the locking and unlocking of the steering wheel.
If you need to remove it, there could be several reasons why. Maybe you need to replace it with a new one or maybe you need to take it apart to clean it. Whatever the reason, here is a guide on how to do it.
The first step is to remove the steering wheel. There are several ways to do this and it will depend on the model of car that you have. Once the steering wheel is off, you can see the ignition lock cylinder.
There are two ways to remove it. The first way is to use a key. Insert the key into the cylinder and turn it until the cylinder comes out.
The second way is to use a screwdriver. Insert the screwdriver into the hole at the top of the cylinder and pry it out.
Once the cylinder is out, you can take it apart if you want. If you need to replace it with a new one, take the old one to go buy a new one at an auto parts store. Then simply put the new cylinder in and reassemble everything.
That is how to remove a Ford ignition lock cylinder from your car’s steering column
Summary
- Remove the steering wheel
- Disconnect the wiring harness to the ignition lock cylinder
- Unscrew and remove bolts from around the ignition lock cylinder
- Take out wires from the ignition lock cylinder and install a new one
- Reinstall all screws, bolts, and wires in reverse order of removal
- Replace steering wheel and reconnect wiring harness to the ignition lock cylinder
The Ford ignition lock cylinder is an important part of your vehicle. It is the device that keeps you from driving your car without a key.
If you’re wondering how to remove it, this blog post will show you how with easy-to-follow steps and pictures.
Here’s how you can remove the ignition lock cylinder on your Ford without the key. The process is simple but requires some time and patience to complete successfully.
First, turn off all power sources for your vehicle before removing any parts or loosening anything that could cause an electrical spark.
Next, disconnect the battery cables from their terminals to prevent accidental sparks when working near the battery area of your vehicle. Follow this by removing all visible screws holding down panels in place under the steering wheel column and center console area.
Gently lift up each panel so it lays flat against its corresponding surface around it with a little bit of slack between them as shown below: Now use a flat blade screwdriver to pry out these plastic tabs alongside where they meet the metal frame of the steering column as circled in red below. There’s one on each side.
Once they’re all popped out, the entire center console and steering column shroud can be lifted up and removed.
With all the screws removed and panels lifted, you should now be able to see the ignition lock cylinder in its entirety. It’s the round silver object right in front of you.
Slightly pry it up from its surrounding area using a flat blade screwdriver to see how it’s connected at its bottom and underside, and if any more screws need to be removed so it can come out.
Why would you need to remove a Ford ignition lock cylinder?
The ignition lock cylinder is a small, usually square device that fits into a car’s steering column. It has a keyway and a few grooves for the key to turn it.
Just inside the tip of the keyway, there are metal contacts that tell the car if the right key is being used.
If the ignition lock cylinder fails, the car will not start. You can replace an ignition lock cylinder that has failed or a new one that doesn’t work properly because of a worn ignition lock cylinder cam and keyway.
In order to remove an ignition lock cylinder from a steering column, you have to remove the ignition switch from its housing so you can get to the ignition lock cylinder.
- Remove the ignition switch from the ignition housing by removing the two screws on either side of it.
- Insert an ignition lock cylinder removal tool into the keyway and turn it counterclockwise to remove the ignition lock cylinder.
- Reverse these steps to install a new ignition lock cylinder.
How do you release an ignition tumbler?
Here is a simple step-by-step guide to releasing an ignition tumbler:
Step 1: Access Your Ignition System
First, you will need to access the ignition system in your car. To do this, locate the hood release lever in your vehicle; the hood release is usually marked with a lever that has a red line painted on it.
Step 2: Locate the Ignition Tumbler
Once you have located the ignition system, you will be able to locate the tumbler as well. The tumbler is usually on the front of the main ignition assembly.
Step 3: Remove the Ignition Tumbler
Once you have located the tumbler and identified all the other components, you can remove it. You must use a socket wrench, which is easy to find at most home improvement stores.
Step 4: Replace the Ignition Tumbler
Once the old tumbler has been removed, you can now replace it. To do this, line up the new tumbler with the hole and plug it into place.
How do you unlock a stuck ignition?
The first thing you should do is to check to make sure the shifter is in Park or Neutral. Since most cars today have remote keyless entries, the shifter being in the wrong position could cause the ignition to be stuck.
The next step is to check to see if a mechanical issue is causing the key to jam in the ignition. This could be a sign of an ignition switch or faulty key.
How do you pick a cylinder lock?
Here are the steps you’ll need to take:
- Gather the right tools. You’ll need a good quality pick set (found at your local hardware store), a tension wrench, and any optional tools to help grip and accuracy.
- Find the pins. Finding the pins is one of the most important steps in picking a cylinder lock.
- Align the key. Once you’ve lifted the pins, you must line up the key with the spring mechanism.
- Turn the key. Once the key is aligned, it’s time to turn the key and unlock the lock. It may take some effort, and you may need to turn the key multiple times.
How do you pull a cylinder lock?
Here’s a step-by-step guide.
Step 1: Ensure your lock is properly aligned with the door frame. Any misalignment or lack of contact between the pins and the locking mechanism can cause issues.
Step 2: Check the orientation of the keyhole. Ensure that the keyhole is oriented so that the keyhole is in the same direction as the pins inside the lock.
Step 3: Insert the key into the keyhole. Push the key through the keyhole and then turn it clockwise. This will press the pins down and disengage the lock.
Step 4: Move the lock forward. Once the pins have been disengaged, you should be able to pull or push the lock forward with some effort.
Step 5: Take the key out. Once the lock has been fully disengaged, you can remove the key from the keyhole.
How do I remove a single-cylinder lock?
Step 1: Remove the key from the lock cylinder, as the first and most important step. If you attempt to begin removal without the key, you might damage the lock in the process.
Step 2: Unscrew the screws that hold the outside of the lock and the handle together, then gently take out the handle.
Step 3: If the lock has a latch, push it down to release it and take it out.
Step 4: Remove the screws around the outside of the lock to detach the lock body, then slide it out of the door.
Step 5: With the latch and lock body removed, it’s now time to manage the inner portion of the lock, the cylinder.
Step 6: Use a pry bar or screwdriver to remove the screws around the sides and bottom of the cylinder and slide the cylinder out.
Step 7: Once the cylinder is removed, you can unfasten the remaining components of the lock, such as the pins, springs, and pins.
Can a locksmith open a cylinder lock?
Yes, a locksmith can open a cylinder lock. Cylinder locks provide a higher level of security than most other locks, making them an ideal choice for protecting your home or business.
Can you drill out a lock cylinder?
Yes. Drilling is one of the most effective and quickest ways to remove a lock cylinder from any type of door or window.
What holds a lock cylinder in?
The answer is simple — spring-loaded pins. These pins are designed to secure the lock cylinder and provide it with the stability and strength necessary to do its job.
How many pins are in a cylinder lock?
The answer depends on the type of lock you use, but the most common cylinder lock will have six pins. This means that each lock has six individual pins located in its cylinder.
Are all key cylinders the same?
No, they’re not – key cylinders come in many different shapes and sizes, even though they might all have the same basic function.
Removing the Cylinder From the Housing
Removing the cylinder from the housing results in less wear of internal components, but does not allow for firing-pin retraction for safety reasons.
Removing the cylinder allows more reliable maintenance access, easier cleaning, and more accurate calibration of the blaster since there is nothing in front of the plunger tube.
Removing the cylinder from the housing also allows for lighter-dart performance and a more consistent feel between shots, as well as accuracy at greater distances.
Step 1
Take your air blaster and open it up by taking off the four screws on the back and front of the blaster and sliding off the two halves (you may need to pull out the plunger tube for this).
Step 2
Removing the Cylinder From the Housing Once you open up your air blaster, you will see an orange cylinder piece sticking out of a silver base.
Removing this is just as easy as the rest of the blaster. Removing this piece from the blaster will result in a considerable reduction in weight, The first two dots are pointing to a notch at each side offs.
Take your air gun and lay it sideways on a flat surface, with two off-center holes at the bottom of the barrel pointing up towards you.
Replacing the Ignition Lock Housing
If you have lost your key, broken the ignition lock housing or just want to change the look of your car, then you will need to replace the ignition lock housing. This is not a difficult job, but there are a few things that you should know before starting.
The first thing that you will need to do is remove the steering column cover. This can be done by removing the screws that hold it in place. There are usually two or three screws on the bottom and one or two on the top.
Once the cover is removed, you will need to remove the ignition lock cylinder. This can be done by unscrewing it from the housing.
Be careful not to drop it or to lose the rubber membrane that protects the lock from dust and dirt. If you do lose this, then you should order a new one from your dealer.
Once the cylinder is removed, take a good look at the housing and see if there are any signs of wear.
Something might have damaged it in some way. Replacing damaged housing is not a difficult job, but it is a good idea to check first just to be sure.
If you have decided that the ignition lock housing needs replacing, then you will need to purchase a new one from your dealer. Typically they cost between four and six dollars depending on your car’s year and model.
Steps to Removing the Ignition Lock Housing
Step 1: Locating the Lock Cylinder
The ignition lock cylinder is located on the steering column, and it can be seen and accessed by opening the driver’s side door.
Step 2: Removing the Retaining Screw
There is a retaining screw that needs to be removed in order to take the Lock Housing off of the steering column. The screw is located at the bottom.
Once the screw has been removed, the Lock Housing can then be pulled off of the steering column.
Step 3: Loosen the Mounting Bolts
There are two mounting bolts that hold the Lock Housing in place. They can be accessed by removing the cover on the side of the housing.
Once the bolts have been loosened, the Lock Housing can then be pulled off of the steering column.
Step 4: (optional): Remove the Key with the Stuck Ignition Spring by Using an Air Tool
It is possible to remove a lock cylinder with a broken key stuck inside using an air tool. Simply puncture the lock cylinder and tap out the internal components. The internal components could be reused after repairing or replacing them.
how do you remove an ignition lock cylinder without a key f150
If the key has fallen out while the engine is running, it is advisable to not turn off the engine as this will cause the security system to go into operation.
If your key is broken off in your ignition lock cylinder, you’ll need to remove it. This can be a very difficult process and requires a special tool.
The best way to do it is by inserting a screwdriver into the lock cylinder straight into the spot where the key goes.
To remove the ignition lock cylinder without a key, you need to unscrew it first. Start by grabbing your stiff wire or paperclip and inserting it into the switch itself.
Pull the wire out with as much force as possible. Then stick the paperclip into the gap and push it to the right.
Finally, slide out the switch with ease and replace it with a new one.
ford ranger ignition lock cylinder removal without key
In order to change the ignition lock cylinder on your Ford Ranger when it is broken or when you have lost your key, all you need to do is follow these steps.
Start by turning all of your door locks down and covering your steering wheel with a towel so that it doesn’t get scratched.
Use a flat head screwdriver to turn the ignition lock cylinder counter-clockwise so that you can remove it from its slot.
It is a common way to remove it with a paperclip. You need to do the following steps:
- Insert the paperclip deeply into the ignition lock cylinder, and turn it as much as you can.
- Apply force upward to the ignition lock cylinder, and then push the ignition lock cylinder outwards.
- Press the release button while pulling out the switch handle together.
how to remove key cylinder from ignition switch?
Although it might look like there are multiple steps involved in removing a key cylinder from the ignition switch, there are actually only three simple steps that must be followed to successfully remove any ignition lock.
Begin by taking a power drill and using the drill bit to make a hold in the key slot of the ignition cylinder.
After you have made your way around the cylinder, take a screwdriver and insert it into the cylinder from the opposite side that you drilled.
By doing this, you can use the screwdriver to turn the cylinder toward you as far as it can go.
Next, take a straightened-out paperclip and place it on the left side of where your ignition switch is located, but be sure not to push it in too far.
Then, begin inserting your screwdriver into both holes at once until you can see that the two are lined up perfectly.
Once they are lined up perfectly, pull hard on both pieces in opposite directions until you can slide out your ignition switch.
how to remove ignition lock cylinder without key
Changing an ignition lock cylinder without a key is more likely to succeed if the locksmith is well-equipped. Having a power drill, drill bit, flathead screwdriver, and a key blank that matches the ignition lock cylinder will ensure that he can make an exact duplicate of the old ignition key.
- Step One – Disconnect the car battery.
- Step Two – Remove the steering wheel by removing covers and disconnecting wires.
- Step Three – Remove wiper arms, indicators switches etc. Step Four – Unscrew the lock cylinder from its base and then work it out of its housing.
